Toggle search

Search

Toggle menu

15

834

8

5,182

LCD wiki

Navigation

Main page

Recent changes

Help

Special pages

Upload file

Site

English Site

中文站点

notifications

Toggle personal menu

Not logged in

Your IP address will be publicly visible if you make any edits.

user-interface-preferences

Personal tools

Log in

ESP32-32E display module Qucik Start

From LCD wiki

More actions

Tools

What links here

Related changes

Printable version

Permanent link

Page information

1.Download the Quick Start package

A.Find the "Quick Use Instructions" section on the product webpage and click on the Quick Use kit

link to download

B.After downloading the data package, unzip the data package. The contents of

the data package are as follows:

The bin folder contains the bin file to be burned.

The Flash_Download folder contains flash download tools.

USB-SERIAL_CH340. zip is the USB to serial port driver of the computer.

2. Power on the product

Use the Type-C cable with power supply and data transmission function to connect the computer to

the product and power the product. As shown in the picture below:

3. Install the USB-to-serial port driver

A.Decompress the "USB-SERIAL_CH340.zip"package downloaded in Step 1, or download the

"USB-SERIAL_CH340.zip"package from the tools section of the product web pageand decompress it

B.go to the folder after decompression, double-click "CH341SER.EXE" executable program, pop up the

installation window, and then click "Install" button to continue the installation, as shown in the following picture:

C.After the installation is successful, click the window OK button to exit. Connect the computer USB to the

development board and power on, and then enter the computer device manager, you can see that the

CH340 port is identified under the port, as shown in the following picture:

4. Burn the bin file

A.Locate the Flash_Downloadfolder from the Quick use kit downloaded in Step 1, or Download the

Flash_Download.zip package from the tools section of the product web page, decompress it,

and find the flash_download_tool folder, open the folder, and double-click the exe executable

file of flash_download_tool. As shown in the picture below:

B.After opening the Flash download tool, ChipType select "ESP32",WorkMode select "Develop",

LoadMode keep the default (UART), and then click "OK" button, as shown below:

C.Enter the Flash download tool interface, first select the bin file to burn, The bin file is in the "bin" directory

in the Quick use kit downloaded in Step 1, as shown in the following figure:

D.Click the button with three dots in the middle to select the bin file in the above steps. After the selection,

check the box in the front and set the burning address as "0", as shown in the following picture:

E.Set SPI SPEED to "80MHz", SPI MODE to "DIO", and keep other Settings default, as shown in the following figure:

F.Set COM, as long as the product is normally connected to the computer, COM port will be automatically

recognized, click the drop-down menu to select. Set BAUD, click the drop-down menu to select,

the larger the value, the faster the burning speed, but can not exceed the maximum transmission

rate supported by the USB-to-serial chip. As shown in the picture below:

G.Click the "START" button to enter the burning state. During the burning process, the status changes:

"Waiting for synchronous power-on" -> "Downloading" -> "FINISH", and the progress bar will also

be loaded, as shown in the following picture:

5.Run the program

After the Bin file is burned, press the reset button of the product or power on the product again,

and you can see the operation effect of the program, as shown in the figure below:

Retrieved from "http://www.lcdwiki.com/index.php?title=ESP32-32E_display_module_Qucik_Start&oldid=5050"

Last modified

This page was last edited on 15 September 2024, at 11:06.

LCD wiki

Privacy policy

About LCD wiki

Disclaimers

Technical support Email: [email-masked], Email: [email-masked]